Rene Herse Tyre Mounting Instructions
Here's a quick guide on how to correctly mount Rene Herse Tyres.
Mounting Supple Tyres
• Rotational direction: Rene Herse tyres can be mounted in either direction.
• Supple casings make Rene Herse tyres fast and comfortable, but they don’t hold their shape by themselves like stiffer tyres. A little extra care is needed when mounting Rene Herse tyres on your rims.
• Inspect the rim tape to make sure it covers all spoke holes. With tubeless compatible rims, always use tubeless rim tape, even when using tubes.
• Check the valve hole. Remove sharp edges before mounting the tyre.
Installing The Tyre With An Inner Tube
• Place one bead of the tyre into the rim well.
• On tubeless-compatible rims, make sure the bead is in the curved “well” in the centre, not on the flat “shelves” on the sides of the rim bed.
• Barely inflate the tube so it holds its shape. Insert it into the tyre.
• Push the second bead over the rim sidewall into the “well”, starting opposite the valve. Push the valve inward as you push the last bit of the bead over the sidewall. It may be necessary to deflate the tube at this point.
Check The Tyre Seating
• Push the tyre sidewall inward and check that the tube is not trapped between tyre bead and rim.
• Inflate the tyre lightly (1.7 bar/25 psi). Check the line that is molded into the tyre sidewall (see below). Do this on both sides of the tyre.
• Where the line is not visible, push the tire outward until the line appears (above). Do this all around the tire, until the line is even and parallel to the rim edge, on both sides of the tire.
• Inflate the tire. To allow the tube to seat well, deflate and re-inflate the tire.
• Check that your tire is seated properly before every ride.
Never Ride On A Poorly Seated Tyre!
• If you cannot get the tyre seated correctly, do not ride the bike! The tyre can blow off the rim, resulting in serious injuries.
• Take your bike to a qualified bike shop, together with these instructions, and ask them for help with installing your tyre.
Many Rene Herse tyre models are tubeless-compatible. Refer to the packaging to see whether your tyres are tubeless-compatible. Tubeless-compatible tyres can be used with inner tubes, or set up tubeless (with a sealant) on tubeless rims. We highly recommend Orange Seal or Panaracer Smart Seal for initial set up. Stan’s sealant works well for later topping-up as it does not dry out as quickly. Maximum recommended pressure for tubeless is 4.1 bar (60 psi).
For your safety, perform the following inspection before every ride:
• Check that your brake pads are properly aligned. Squeeze the brakes hard. The pads must not come within 1 mm of the top of the rim. Check the pads: If a ridge has worn into the pads, then they are misaligned and can cut the tyre sidewall and cause a blowout.
• Inspect your tyres to make sure they are seated correctly. Refer to the instructions on the previous pages.
• Do not exceed the maximum tyre pressure listed on the tyre sidewalls. Do not ride the tyres underinflated, so that they bulge out excessively. Either can cause a blowout and serious injuries.
We warrant our tyres against defects in materials and workmanship for one year after the original purchase. If the product is found defective by Rene Herse Cycles, we will replace or repair it. If you feel that a product is defective in materials or workmanship, please send the product to us for evaluation. Please allow up to four weeks for the evaluation. This warranty does not cover:
• Damage due to improper mounting.
• Damage due to punctures, cuts or other road debris.
• Poor seating on out-of-spec rims (Velocity Synergy, Specialized Axis 4.0, etc.)
• Abrasion due to misaligned brake pads.
• Normal wear and tear; exposure to sunlight or noxious